Tag: construction base foundation

The Underpinning Methods and Foundation

Published / by admin / Leave a Comment

Underpinning can be used to strengthen and repair building foundations. Here we will discuss underpinning techniques, Rectify Underpinning Melbourne as a whole, the types of work that can be done with underpinnings, and structural conditions that require underpinning. It is possible that a foundation failure or footing occurs after both the superstructure and substructure have been completed.

In such circumstances, a method of stabilizing the structure must be suggested. Underpinning is a method that helps reinforce a structure’s structural foundation or infrastructure. They include the addition of highly durable or temporary support to an existing foundation in order to achieve extra depth and bearing capacity.

Selecting Underpinning Methods

The type of work and the age of a structure determines which underpinning method is used. Structures are classified based on their age.

Old Structures: Ages of more than 150 years.

Recent Structures: Between 50 and 150 years.

Modern Structures: Under 50 year olds.

Selecting Methods for Selection of Work

Conversion Works

-Protection Works

-Remedial Works

Conversion Works

It is necessary to change the structure into a different capacity that requires a more solid foundation than existing

Protection Works

Protective works are required for the accompanying problems of a building:

The foundation that is currently in place does not appear to be stable or solid.

The soil supporting the existing footing would be affected by the removal of nearby material.

Stabilization of foundation soil in order to resist normal disasters.

Requirement for a storm cellar to be built under existing structures.

Remedial Work

Subsidence of the building was caused by mistakes in foundation design.

Work on the existing structure before building a new one.

Structures that require Underpinning

Engineers may recommend underpinning methods for substructure adjustment for several reasons, including:

Degradation of the timber piles used as foundations for most structures will cause settlement. The water table fluctuations are responsible for this debasement.

The soil can settle due to a reduced bearing capacity caused by the rising and falling of the water level.

Structures that are built on soils with inadequate bearing capacities will settle.

The Need for Underpinning

Observable data can help determine the choice for underpinning. When a structure begins to change, either through settlement, or distress of any kind, it’s important to establish vertical readings, just like at the offset levels, on a perfect premise. How extreme the settlement is will determine the time frame.

Experts must examine and determine the ability of the soil to resist the construction that will be built on it before exhuming the soil for a new project. A decision is made based on the report to choose underpinning. In some cases, such tests would not support being done until the whole structure has been developed.

The Underpinning Methods

The following are some of the different methods used for reinforcing foundations:

-Mass Concrete Underpinning Method (Pit Method)

Underpinning using the Cantilever Needle Beam method

The pier and beam underpinning method

Mini Pilled Underpinning

The pile method of underpinning

Pre-test Method for Underpinning

No matter what type of foundation reinforcement method is chosen, they all follow the same idea of extending the existing foundation in either a long or wide direction and laying it over a deeper soil layer. The load can be distributed over a larger area. In the following areas, we will briefly mention different underpinning techniques. Underpinning method selection is based on the soil conditions and required foundation depth.

Mass Concrete Underpinning Method (Pit Method)

The mass concrete method, or pit method has been used for centuries. This method involves extending the existing foundation until it reaches a solid stratum. In stages, the soil beneath the existing foundation is exposed. When the strata is suitable, the soil is covered with concrete, and the excavation is saved to cure before the next step is undertaken.

Another pin through the dry sand cement pack is used to move load from an old foundation onto a new one. It is an inexpensive method that works well for shallow foundations. Other methods are available for more complex foundation issues.

Cantilever Needle Beam method of underpinning

Underpinning with cantilever beams is a common extension to the pit method. This method is used for underpinning if only one side of the foundation needs to be extended and there’s a column within the plan.

Cantilever Needle Beam: Advantages

It is quicker than the traditional method.

It has only one access on the side.

It has a high carrying capacity.

Cantilever Needle Beam method: Disadvantages

The foundations are so deep that digging is not economically viable.

The use of needle beams is limited by the access restrictions.

The Pier and Beam Method of Underpinning

This method was also known as the base-and beam technique, and it began to be used after World War II. The mass concrete technique was not able to provide a good foundation for large depths. This method is feasible for most ground conditions. The load is transferred to the mass concrete base or piers by using reinforced concrete beams. The ground conditions and the applied loads determine the size and depth of the beams. The beams are found to be practical at depths less than 6.0m.

The Mini-Pile Underpinning

The method works well when the soil is difficult to access, or if the environmental impact is a problem. The piles are driven between the sizes of 150-300 mm. They can be driven with steel casing or forecast.

The Pile Method is a method of underpinning

This method of underpinning involves driving piles on the adjacent sides to the divider, which supports the weak foundation. The divider is penetrated by a needle or pin. The needles are used as pile covers. This method can treat soil that has settled due to water clogging, or because it is clayey.

Test Method for Underpinning

Use it for strip or pad foundation. This can be used for 5.0 to 10 story buildings. The subsoil will be compacted and pressed in the removal level, which gives the soil the predetermined loads. It is carried out before the underpinning technique is used. Normal is for there to be a reduced level of clamor or interruption. The method cannot be used for the raft’s foundation.

Here we will discuss what underpinning is, how to choose the right method, which structural conditions require underpinning as well as underpinning techniques.